Configure the Anybus Wireless Bridge II
Switch a Quantum from Control App 7 to Control App 8, using the Windows tablet you already use with it.
Quantum connects to the Control App through a Bluetooth unit built into the machine, the HMS Anybus® Wireless Bridge II™. If you use your Quantum with Control App 7, the Bluetooth unit needs new settings before the Quantum works with Control App 8 or with Android tablets. You can change the settings yourself from the Windows tablet or PC that you already use with the Quantum, over Bluetooth. No cables are needed.
This page is only for a Quantum that is set up for Control App 7. New Quantum machines and new Bluetooth units are delivered with the correct settings. For a Sprint 1, contact 1080 Motion support.
Do not open the machine
Never open the Quantum to reach the Bluetooth unit. If you can't make the change as described here, contact 1080 Motion support.
Do not use Factory Reset or PROFIsafe mode
In the unit's web interface, never click Factory Reset on System Settings, and never select Easy Config mode 11, Enable PROFIsafe mode, on the Easy Config page. Both leave the Quantum unable to connect to the Control App until 1080 Motion support sets up the unit again.
Find your Quantum's addresses
Each Quantum position has its own unit address, start address and starting IP. You need them in the steps below.
| Quantum | Unit address | Start Address (Y) | Starting IP |
|---|---|---|---|
| Single Quantum, or LEFT Quantum of a synchro pair | 192.168.250.99 | 111 | 192.168.250.111 |
| RIGHT Quantum of a synchro pair | 192.168.250.98 | 222 | 192.168.250.222 |
Switch to Control App 8 from your Windows tablet
You change two settings on the Bluetooth unit, over the same Bluetooth connection that Control App 7 uses.
Before you start, check that:
- The tablet is paired with the Quantum and has the manual address described in IP Settings.
- No other tablet or PC is connected to the Quantum. It accepts only one connection at a time.
If you don't see a setting
If a setting in these steps is missing, for example Layer 3 IP forward under Bridge Mode, the Bluetooth unit's firmware needs to be upgraded. Click Cancel All Changes, and contact 1080 Motion support to get the firmware upgraded.
-
Turn on the Quantum and connect to it from Control App 7, as you normally do. Keep the Control App open, so that the Bluetooth connection to the Quantum stays open while you work in the web browser.
-
Open a web browser on the tablet and go to the unit address,
http://192.168.250.99, orhttp://192.168.250.98for the RIGHT Quantum of a synchro pair. The unit's web interface opens on System Overview. -
Recommended: open System Settings and click Generate under Settings Backup. This saves a copy of the current settings that you can load again with Restore Settings.
-
Open Bluetooth Settings and set Bridge Mode to Layer 3 IP forward. Leave the other settings as they are.
-
Open Network Settings. Under Internal DHCP Server, select DHCP Server Enabled and set DHCP Interfaces to Wireless Interfaces. Then set Start Address (Y):
- Single Quantum, or LEFT Quantum of a synchro pair:
111. The starting IP is then192.168.250.111. - RIGHT Quantum of a synchro pair:
222. The starting IP is then192.168.250.222.
Leave the other settings as they are.
- Single Quantum, or LEFT Quantum of a synchro pair:
-
Click Save and Reboot. The unit restarts, and the Control App loses its connection to the Quantum.
-
On the tablet, set the IP assignment of the Bluetooth Network Connection back to Automatic (DHCP). It is in the same place where you entered the manual address. See IP Settings.
-
Wait about a minute for the unit to restart, and then connect to the Quantum from Control App 8.
Nothing changes on the unit until you click Save and Reboot. If the connection drops before that, connect again and check the settings before you save.
Your Quantum now also works with Android tablets. See Android tablets.
Troubleshooting
- A setting from this page is missing in the web interface. The Bluetooth unit's firmware is too old and needs to be upgraded. Click Cancel All Changes, and contact 1080 Motion support.
- The browser can't open the unit address. Check that Control App 7 is connected to the Quantum, and that the tablet's Bluetooth Network Connection still has its manual address,
192.168.250.111or192.168.250.222. - The tablet can't connect after the unit restarts. Check that the tablet's IP assignment is Automatic (DHCP). If it still can't connect, remove the Quantum in the tablet's Bluetooth settings and pair it again.
- A tablet or PC can't pair or connect. Only one device can be connected at a time, so disconnect any other tablet or PC. On Bluetooth Settings, check Paired Devices. Click Unpair next to devices that should no longer connect, click Save and Reboot, and pair again.
- A tablet doesn't get an address with Control App 8. Check that Bridge Mode is Layer 3 IP forward, Internal DHCP Server is enabled and DHCP Interfaces is Wireless Interfaces. A connected tablet appears in the DHCP Table on Network Settings, with an address from the start address upwards.
- Something else doesn't work. Contact 1080 Motion support.